Fibre in Duct or Point-to-Point Wireless Between Buildings?

Linking outbuildings, gatehouses and guest wings

Published November 2026 · Custom Controls · Home network and smart home specialists since 1998

Almost every large property ends up with buildings that need to be on the network but are not attached to the house: a garden room or cinema, a boathouse, a gym, a gatehouse, staff accommodation, a garage with a flat above it, an estate office. Each of them is a small version of the main house, with cameras, access control, audio, heating controls and people who expect the wifi to work, and each needs a link back to the core of the network. The choice is between putting a cable in the ground and sending a radio signal across the gap.

Both are legitimate engineering, and both go wrong when they are chosen for the wrong reasons. Fibre in duct is the better link wherever it can be laid, and we lay it wherever ducts can be installed. Point-to-point wireless earns its place where a trench is impossible, forbidden or disproportionate, and when it is designed and installed properly it is a dependable bridge rather than a compromise. The decision turns on the route, the distance, the electrical environment, the capacity needed and what has to keep working when something fails.

This guide sets out how we compare the two for large homes and estates: what fibre actually gives you, how the duct route should be designed, where wireless is the right answer, what protects either link from lightning and power faults, and how to build a hybrid that uses both. It sits alongside our network design for new builds and renovations service, which plans these routes before the ground is dug.

Why Buildings Need a Proper Link

A detached building on an estate is not an extension of the house’s network by default. It is a separate place, with its own electrical supply or at least its own distribution, often at a different earth potential, and with different demands from the house. A cinema in a garden room needs enough bandwidth to stream and a reliable connection to the control system. A gatehouse needs its door station, cameras and gate controller reachable at all times. Staff accommodation needs internet access and, if it shares the estate’s network, proper separation from the family’s.

The temptation, particularly when the building was an afterthought, is to improvise. A powerline adapter, a mesh node placed in a window, or a consumer wireless bridge pointed at the house works for a few weeks and then becomes the weakest link on the estate. Cameras drop, the cinema buffers, and the door station that someone is relying on fails silently. A link between buildings carries the same expectations as the rest of the network, and it deserves a design with the same care.

It is also worth remembering that the link is the part of the network most exposed to the elements. It crosses open ground, passes through weather and sits at the mercy of anything that digs, builds or grows between the two ends. The question is therefore not only how much data it can carry, but how it is protected, how it is powered and how we will know if it fails.

What Fibre Gives You

Fibre carries light through glass, not electricity through copper, and that has practical consequences for a link between buildings. It does not conduct electricity, so it cannot carry a surge from a lightning strike or a fault from one building to the other, and it removes the problem of differing earth potentials between the buildings. Copper cable between two buildings, by contrast, can carry a surge or a ground potential difference straight into the equipment at either end, which is why a copper run between buildings needs careful protection and is not our first choice.

Fibre also has more capacity than any wireless link, and it keeps that capacity as requirements grow. The cable laid today for a gigabit link will carry multi-gigabit or higher speeds simply by changing the equipment at each end, which is why the cable is the lasting investment and the electronics are the part that is replaced. That headroom is valuable on an estate where a cinema, cameras and a guest wing may all be using the link at once, and where nobody wants to dig the same trench twice.

Distance is rarely the limiting factor. Over multimode fibre, the common 10 gigabit standard reaches 300 metres on OM3 and 400 metres on OM4. Over single-mode fibre, the 10 gigabit long-reach standard is rated to 10 kilometres. A copper Ethernet cable is limited to 100 metres. Single-mode is the sensible choice for new runs between buildings, because it has no practical limit on a private estate and does not constrain what can be connected to it later. The fibre itself is usually a small part of the total, which is why the ducting is where the design effort goes.

Designing the Duct Route

A duct route is a civil engineering exercise, and it is best planned before the landscaping, the drive or the new building goes in. The aim is a protected path that can be added to later: a duct, not a buried cable, so that fibre can be pulled in, replaced or supplemented without excavation. We specify ducts with spare capacity, so that a second fibre, a power cable or a future requirement can use the same route, and chambers or draw points at changes of direction and along longer runs so cables can be pulled without strain.

The route itself needs surveying with the same attention as any other service. It has to avoid existing drains, power and water, root systems, planned planting and any future building footprint, and it has to be recorded accurately. As-built drawings and surface markers matter, because the most common cause of a fibre fault on an estate is the next contractor digging through it. Warning tape in the trench and a record on the property plans are inexpensive protection against the most predictable failure.

At each end the fibre arrives at a termination point in a protected enclosure, usually a patch panel in a cabinet or comms room, with the cable fixed, labelled and given a service loop so it can be re-terminated. We terminate by fusion splicing or with factory-terminated assemblies, and test every link with light source and power meter or an optical time-domain reflectometer, recording the results with the as-built information. The test record is what shows, years later, whether a link has degraded, and it belongs in the network documentation.

  • Ducts with spare capacity for future fibres and services, instead of a single direct-buried cable.
  • Chambers at changes of direction and along long runs, so cables can be pulled in without damage.
  • Accurate as-built records with surface markers and warning tape, to protect against the next dig.
  • Enough fibre cores for separate links, such as the network, cameras or a second path, not just one.
  • Tested and recorded terminations at both ends, kept with the network documentation.

Powering the Building at the Far End

Fibre carries data and not power, so a building at the end of a fibre link needs its own power for the network equipment, and the design has to make sure that power is as dependable as the link. A switch in a garden room that loses power when the room’s circuit trips is a link that has failed, however good the fibre is. For buildings that matter, such as a gatehouse with the door station and cameras, the network equipment should be on a dedicated supply, ideally with battery backup, so that a short outage does not drop the network and the devices that depend on it.

Inside the far building, power over Ethernet from the switch can then supply access points, cameras and other devices, which is how a single fibre link and a single protected switch can support a whole building. The cabling inside the building should be to the same standard as the house, with certified copper to each outlet and access point position, so that the building is a first-class part of the network and not a special case.

Where the building has its own consumer unit and its own supply, we also consider the electrical relationship between the buildings, which is another reason to prefer fibre: it keeps the two electrical systems isolated from one another for data purposes, so a fault or a surge on one does not propagate through the network to the other.

Garden speaker disguised as a rock on a timber deck in the grounds of a Dubai estate, one of many outdoor audio zones

When Point-to-Point Wireless Is the Right Answer

There are many sites where a trench is not possible or not sensible. A route across a road or a river, through rock or established woodland, over land the owner does not control, or through ground whose ownership, drainage or heritage status makes digging a problem, can make fibre uneconomic or impossible. A listed or protected landscape may forbid new trenching. A building that is only needed for a season, or a temporary arrangement during a build, may not justify the groundwork. In these cases a point-to-point wireless bridge is the right tool.

A properly designed wireless link is not a consumer extender. It uses two directional radios, one at each building, mounted on a mast or wall at a height that gives a clear path between them. The radios must see each other, and not only in the narrow sense of line of sight. The signal travels through a zone around the direct line called the Fresnel zone, and obstructions inside it, such as tree canopy, a building corner or a roof edge, weaken the link. The survey therefore checks the whole path at the height the antennas will be mounted, and allows for growth in trees between survey and a summer storm.

The radios are then aligned carefully, because a narrow beam a few degrees off will perform far worse than one that is correctly aimed, and tested for signal strength and throughput after installation. Wireless links will carry less than fibre, will vary a little with weather and interference, and need to share the radio spectrum with other users, but a well-chosen pair of radios on a clear path can provide a dependable, high-capacity bridge that serves a building’s real needs.

Protecting a Wireless Link: Earthing, Surge and Power

An outdoor radio on a mast is an obvious target for lightning, and the cable running from it into the building can carry a surge into the network. Protection is a standard part of a professionally installed link: the mast and radio are bonded to earth, the radio’s Ethernet cable is shielded outdoor-rated cable with the shield grounded, and surge protection is fitted where the cable enters the building. The same protection is fitted at both ends, because a surge can arrive at either.

The radios are normally powered over Ethernet from a PoE injector or switch inside the building, which keeps the powered equipment indoors where it is protected and where it can be put on the same battery backup as the rest of the network. The cable from radio to building is kept within the 100-metre Ethernet limit, and routed and sealed so water cannot enter the connectors, which is a more common cause of failing links than the radios themselves.

Mounting matters as much as electronics. A radio on a flexible pole or a flimsy bracket moves in wind and drifts out of alignment, so we fix radios to rigid structures and re-check alignment after the first storms. The end result is a link that is documented, protected and monitored like every other part of the network.

Spectrum and Regulation in the UK

Wireless links use shared radio spectrum, and the rules are set by Ofcom. Ofcom has made the 5725 to 5850 MHz band licence-exempt for fixed wireless access, which is the band most point-to-point bridges use, subject to the conditions in its guidance, and it has also been opening up more of the 6 GHz band for Wi-Fi. Its decisions include allowing outdoor and higher-power Wi-Fi in the lower 6 GHz band, provided the devices operate under the control of an automated frequency coordination system. Equipment sold for use in the UK is designed to comply, and an installer should confirm that a particular radio and configuration meet the current conditions before relying on it.

Because the rules and the equipment are both changing, we check the current position when specifying a link, and we choose radios from established manufacturers that are approved for UK use. The practical point for an owner is that unlicensed spectrum is shared. A neighbour’s radios, a new installation nearby or a change in the local environment can add interference after the link is working, which is one more reason to monitor links and to leave headroom in the design.

Comparing the Two Options

Neither option is universally better. The table below sets out how they compare on the things that matter for a link between buildings on a large property, and the right choice follows from the route and the building’s needs.

Consideration Fibre in duct Point-to-point wireless
Capacity Very high, and upgradable by changing the equipment at each end High on a good path, but limited by the radios and shared spectrum
Electrical isolation Complete, because fibre does not conduct electricity Good, but the radio’s cable and mast need earthing and surge protection
Installation Needs a trench or existing route, with ducts and chambers Needs a clear path and rigid mounting at both ends
Weather and interference Unaffected Largely unaffected by weather, but exposed to interference and path changes
Future growth Spare ducts and cores allow more links Capacity is fixed by the radios; more links need more radios
Best suited to New builds, landscaping projects, any route that can be dug Routes that cannot be dug, temporary buildings, heritage or protected ground

The one-line summary is that fibre is the permanent answer and wireless is the practical one. Where both are possible, we choose fibre. Where only wireless is possible, we design it as carefully as we would fibre, with a surveyed path, rigid mounting, earthing and surge protection at both ends, and monitoring from the day it is switched on.

The comparison also changes with the building. A gatehouse that carries the door station, cameras and gate controller justifies fibre and a standby path, because its failure is a security problem. A summer house used for a few months of the year may be perfectly served by a single wireless link, because its failure is an inconvenience. We make that judgement with the owner during the design, and write down the reasoning, so that the choice is understood and can be revisited if the building’s use changes.

Swimming pool and raised seating in the grounds of a Dubai estate, with villas beyond

A Hybrid Design: Fibre Plus a Wireless Standby

The most resilient arrangement for a building that matters is both. Fibre in duct is the primary link, and a wireless bridge provides an independent second path. Because the two use different media and different routes, a single event, such as a digger through the duct, a surge or a failed switch, is unlikely to take out both. The network’s switching is configured so that traffic uses the fibre normally and moves to the wireless link if the fibre fails, and our monitoring tells us when that happens.

This is particularly valuable for buildings that carry security and access: a gatehouse, an estate office, or staff accommodation where people rely on the network. The wireless link adds only a pair of radios and some switch configuration to the design, and it turns a link whose failure would be an emergency into one whose failure is a routine repair. Our managed home network service monitors each link and the failover between them, so that the household usually does not notice a fault.

Whichever route is chosen, the final step is to treat each building as a managed part of the same network, with its own segment, its own switch and its own entry in the documentation, so that the link between buildings is understood, tested and recorded and does not depend on anyone’s memory.

Basketball court in the grounds of a Dubai estate, part of a two-villa Crestron installation

Case Study: Dubai Crestron Install, Award-Winning Estate

Our Dubai estate is the most comprehensive residential system we have delivered. It covers two villas, one for the family and one for guests, staff, offices and classrooms, set in grounds that include a swimming pool, a basketball court, a lake and a stream. Eight Crestron processors provide integrated control, and the project won the Crestron Integration Award for Best International Project in EMEA.

The system reaches well beyond the buildings. The basketball court, the pool and the gardens each have their own audio systems, the garden firepit is controlled by the system, and full IP CCTV runs over an enterprise-grade gigabit network with wifi access points throughout both villas and across the grounds.

When a property is made up of two villas and extensive grounds, the connections between the buildings and the outdoor areas carry everything the estate depends on. How those links are made is a decision for the design stage, before the landscaping is finished.

Frequently Asked Questions: Linking Buildings

  • Is fibre better than wireless between buildings?
    Where a duct can be laid, yes. Fibre has far more capacity, is unaffected by weather and interference, and electrically isolates the two buildings. Wireless is the right answer where a trench is impossible or disproportionate, and a well-designed link serves most buildings’ needs.
  • How far can fibre run between buildings?
    Further than any estate requires. On multimode fibre the common 10 gigabit standard reaches 300 metres on OM3 and 400 metres on OM4, and on single-mode fibre the 10 gigabit long-reach standard is rated to 10 kilometres. Copper Ethernet is limited to 100 metres.
  • Why not just run an Ethernet cable to the outbuilding?
    A copper cable between buildings can carry surges and differences in earth potential into the equipment at either end, and it is limited to 100 metres. Fibre avoids both problems, which is why we prefer it for any route that can be ducted.
  • Does a wireless bridge need line of sight?
    Yes, and a clear Fresnel zone as well. The survey checks the whole path at the height the radios will be mounted, allowing for trees to grow and for buildings or roofs close to the line.
  • Is a point-to-point wireless link legal in the UK?
    Ofcom has made the 5725 to 5850 MHz band licence-exempt for fixed wireless access, subject to the conditions in its guidance. We confirm the current rules and use approved equipment for each installation.
  • What happens to the link in a power cut?
    Fibre and the wireless radios need powered equipment at each end. For buildings that matter, the network equipment is on a dedicated supply with battery backup, so that a short outage does not drop the link.
  • Can you use fibre and wireless together?
    Yes, and for important buildings it is the most resilient design. Fibre is the primary link and a wireless bridge is an independent standby, with the network switching automatically if the fibre fails and our monitoring alerting us when it does.

Network Design for New Builds → · Managed Home Network → · Network Audit and Rescue → · Discuss your estate →

«
»